Product Description:

SILICOFIX-MM10 is a performance enhanced normal “thick joint” masonry mortar for bonding various masonry materials like Concrete Blocks, AAC Blocks and Red Clay bricks in thicknesses varying on around 10mm. It is modified to ensure sufficient workability and open time and bond strength to effectively bond various building materials.

SILICOfix MM10 is manufactured by M/s. Precise Conchem Pvt. Ltd., at their plant located at GIDC Panoli, Bharuch District of Gujarat in an automated process according to formulations based on various products studies and research undertaken. The plant is one of the most modern Plants in India, in which all the critical manufacturing processes and operations are completely controlled by P.L.C SYSTEMS (Programmed Logic Controller). The plant has the capacity to produce 25,000 bags @ 40 kg per bag of Polymerized Dry mix Mortar/Plaster per day. This plant can be remotely monitored through CCTVcameras installed within the plant area. The company assure, seamless supply of 100% consistent high quality mortars and plasters at all point of times, round the year.

Download PDF
TECHNICAL PARAMETERS

Appearance and Color

Free Flowing Granular Grey Powder

Binder

Ordinary Portland Cement 53 with Pozzolanic Materials

River SandSand Gradation

Processed Fine Aggregates(Purified, Graded And Proportioned River Sand

Maximum Aggregate Size

3.00 mm

Mixture Proportion

1:6

Additives

Performance enhancing Proprietary additives to improve:

Spreadability& Workability

Strength & Durability

High Bond Strength

Water Resistant

Non-Shrinkage

Water Retention

Water Demand

13% to 14%

Pot Life

60 mins to 90 mins

Dry Density

1.75 kg/L

Wet Density

2.10 kg/L

Compressive Strength at 28 Days

10 MPa to 12 MPa

Packaging

40 kg per bag

Advantages
METHOD OF APPLICATION
Clean surface of the block or brick before application so that the surface is free from dust, loose particles which mayaffect the adhesion of SILICOfix. The block or bricks must be saturated well with water before application of SILICOfix MM10 Block Jointing Mortar. Take 8 liters to 9 liters of potable water depending upon the thickness of the joints to be built-up for one full bag of 40kg SILICOfix MM10 powder. Pour the minimum required quantity of water in a mixing tray of suitable size. Add half the takenquantity of SILICOfix MM10 in the first instant and immediately start mixing. If you delay you will get lumps that you will struggle tomix out. Add the remaining quantity of SILICOfix quickly, but gradually and again start mixing thoroughly until a smooth, creamy, lump-free homogeneous and cohesive consistency mixture of SILICOfix MM10 is achieved. For proper activation ofadditives/polymers in SILICOfix MM10, allow the mixture to stand/rest without disturbing for 2 minutes. Remix for a minute. Ifnecessary make it up with addition of little extra quantity of water to achieve required consistency, remix once again fora minute. Now the SILICOfix MM10 mixture is ready for use/application. Do not add extra water to the mixture than prescribedabove, as addition of extra water will lead to loss of strength and create microscopic and /or visible pores. Using a proper notched trowel, apply a thin and uniform layer of SILICOfix Mortar in thickness of 10 mm in horizontaland vertical joints of the block and then place the block above it. Clean the excess flush material to clean the joint areasand reuse the same immediately. Continue laying the next block with the same procedure to complete the masonry wall.SILICOfix MM10 should be applied within 60 minutes to 90 minutes of its preparation.
Shelf Life
  • 3 Months, if kept in cool, dry condition in unopened original packing.
Packaging
  • 40 kg Bag
WARRANTY

The Products supplied by the Company are warranted to comply with the Product Specifications mentioned in the Product Brochure, provided they are applied and used in conformance with the processes and procedures described in the Brochure and as per the Standard Civil Engineering Practices.

In the unlikely event that the Products are found to be not in compliance with the mentioned specifications, the Company undertakes to replace the Products that are specifically determined to be non-compliant. Any suspected defects or non-compliance of the Products must be reported to the Company in writing within 72 hours of being detected or within 45 days of the supply of the Products, whichever is earlier. The Company shall have the right to inspect the area where the suspected defects are detected and in case any such suspected defect is determined to be caused specifically due to a deficiency in the Products supplied by the Company, the Company undertakes to provide replacement only for the specific area where the defective Product was applied, and not for the whole room, floor, building, or project where the Company’s Products may have been used.

Since the Company does not have control over the installation or application or end use of the Products, the Warranty shall not cover any defects that may be caused due to defective or faulty or unskilled workmanship, application, curing, or treatment of the Company’s Products. The Warranty is limited only to replacement of the Products in question and does not cover any incidental and consequential costs or damages including, but not limited to, the costs of removal and reapplication of the Products, delays, loss of profits, or any other liabilities that the purchaser may incur towards any third parties.

The above Warranty is the complete set of Warranties offered by the Company on its Products and overrides any other Warranties that may be implied or expressed in any other Product Literature or that may erroneously be inferred by the purchaser through interactions with the Company’s representatives or with any consultants, architects, etc.

The Company may, in the interests of customer service, relax the above Terms of Warranty. Any such relaxation shall be at the sole discretion of the Company and shall not be taken to be a precedent for the future. Such relaxation can only be authorized in writing by the CEO / Directors of the Company and no Company representative shall have any rights to relax the Terms of the Warranty without explicit authorization in writing from the CEO / Directors.

DISCLAIMER

All recommendations, suggestions, statements and technical data provided in this Leaflet are based on the best current knowledge available and are given for illustrative and informative purposes only and the Company does not bear without any responsibility for any loss or damages that may be caused by the use / misuse of such data.

It is assumed that all Standard Civil Engineering Practices shall be adopted for the use and application of the Company’s Products and all information provided in this Leaflet is based on the above assumption. The Company shall not be responsible for any loss or damages that may be caused by a deviation from the Standard Civil Engineering Practices or by any use or application of the Company’s products not in consonance with the information provided in this Leaflet.

The Company supplies products as per the Specifications provided in this Leaflet, and all the information in this Leaflet is for general guidance of the purchasers only. It is not possible, in this Leaflet, to provide information with respect to all potential uses and applications of the Company’s Products and for the various site conditions where the Products may be used.

Therefore, the Company makes no claims herein as to the particular suitability or fitness of the Products for specific applications or purposes. The Company may be contacted directly, if any additional information is required for any specific use or application of its Products, prior to the purchase and use of the Company’s Products by the purchaser.

The Company is continuously striving to improve and develop its products to better meet the industry requirements and to provide superior performance. Therefore the Company reserved the right to modify or improve the Products’ specifications or the information in this Leaflet at any time, without notice. The latest Products’ specifications and information can be obtained by directly contacting the Company.

The Company, as used above, shall refer exclusively to M/s Precise Conchem Private Limited as represented by its Board of Directors, and any communication directed to the Company may be preferred to the contact details of the Company, as provided in this Leaflet.